Airport lighting cables are used in series lighting circuits for runways and control systems. These cables are non-shielded and carry low voltage currents. It uses a combination of linear low-density polyethylene, carbon black and UV inhibitors to meet the track resistant properties. It is used for low and medium voltage power transmission of 600 volts to 5000 volts. These cables are suitable for use in conduit, duct, aerial, and direct burial applications.

Alternator Relays are devices that receive a contact signal that indicate when are necessary to pump the water. The relay close a contact that makes pump Nš 1 operates.

An alternator is an electromechanical device that converts mechanical energy to alternating current electrical energy. Alternators use a rotating magnetic field. The alternators used in modern automobiles usually generate less than 500 watts. There are two types of alternators such as the revolving armature type and the revolving field type. The revolving armature type is similar in construction to the dc generator in that the armature rotates through a stationary magnetic field. The revolving field type of alternator has a stationary armature winding and a rotating field winding. Alternators are designed for varying alternating-current frequencies between sixteen and about one hundred hertz for use with arc lighting, incandescent lighting and electric motors.

Aluminum Back Panel is used in the complete system shelter. This panel has specially drilled holes to fit radio and cell phone installations. This is available with thickness 100″. This is also for use with 8″ x 6″ fiberglass enclosures.

Aluminum building wire is used in service entrance, feeders, and branch circuit applications for residential, commercial, industrial and transportation environments for permanent installations utilizing 600 volts or less. It can be installed as general purpose building wire. It is suitable for directly buried installations and can be used in environments where superior insulation, tochgness, and chemical resistance are required.

Aluminum Conduit/Fittings are a protective pipe or tube through which electric wires or cables are run. It makes an excellent choice for home decor projects. It can be easily cut, threaded, and bent without using special tools. It resists corrosion and does not leave discoloring streaks or stains. It is used to sheath electrical wires. It is used to retrofit for tunnels because the aluminum is light enough to handle, and it does not rust in hard weather. It is mainly used where weight is required to be minimized.

Aluminum electrolytic capacitors use very pure aluminum foil as electrodes, which are wound into a cylinder with an interlayer paper or other porous material that contains the electrolyte. Aluminum ribbon staked to the foil at the minimum inductance location is brought through the insulator to the anode terminal, while the cathode foil is similarly connected to the aluminum case and cathode terminal. Aluminium electrolytic capacitors are constructed from two conducting aluminium foils, one of which is coated with an insulating oxide layer, and a paper spacer soaked in electrolyte. The foil insulated by the oxide layer is the anode while the liquid electrolyte and the second foil act as cathode. This stack is then rolled up, fitted with pin connectors and placed in a cylindrical aluminium casing. The two most popular geometries are axial leads coming from the center of each circular face of the cylinder, or two radial leads or lugs on one of the circular faces.

Aluminum Hinged Deadfront Panels are available with raised cover to add 1.75 inches of depth. The sizes range from 6 x 6 x 4 to 20 x 16 x 8 inches. These are available in lift-off screw covers, hinged screw covers, snap latch hinged cover and twist latch hinged cover. These panels are also used in configuration flexibility.

Aluminum Interlocked Power Cables are designed for general-purpose wiring in residential, commercial and industrial buildings. It has a maximum operating temperature of 90°C in wet and dry locations. It is designed for use on power or control circuits. Armor is impervious to moisture, gas and liquid. It has flame and sunlight resistant PVC jacket and suitable for marine shipboard and offshore oil rig cables. It provides maximum continuous conductor temperature 90°C dry, 90°C wet. It is used in harsh environments where maximum conductor protection is required. It is also used for power, control and lighting circuits in a broad range of commercial and industrial pulp and paper, mining, and petroleum applications. Aluminum interlocked armor cable is recommended as an economical alternative to wire in conduit systems.

Aluminum long barrel lugs are made out of high conductivity aluminum tube. Connectors are prefilled with oxide inhibiting compound & capped at both ends. The surface of these lugs is passivated. These lugs are available in various sizes ranging from 35mm2 to 1200mm2.